CD3 MicroBeads, human (92-01
该试剂用于从人外周血,支气管灌洗液,细胞培养物或者各种组织中正选CD3 T细胞,分离的T细胞可用于T细胞毒性,T细胞活化,HIV感染,信号转导和表面标记表达等研究
01产品图片

02产品简介
该试剂用于从人外周血,支气管灌洗液,细胞培养物或者各种组织中正选CD3 T细胞,分离的T细胞可用于T细胞毒性,T细胞活化,HIV感染,信号转导和表面标记表达等研究
03产品介绍
[Components]
2 mL CD3 MicroBeads, human: MicroBeads conjugated to monoclonal anti-human CD3 antibodies (isotype: mouse IgG2a).
[Size]
For 109 total cells, up to 100 separations.
[Storage]
Store protected from light at 2 - 8 °C. Do not freeze. The expiration date is indicated on the vial labels.
CD3 MicroBeads are supplied as a suspension containing stabilizer and 0.05% sodium azide.
● Buffer: Prepare a solution containing phosphate-buffered saline (PBS), pH 7.2, 0.5% bovine serum albumin (BSA), and 2 mM EDTA. Keep buffer cold (2−8 °C). ▲ Note: EDTA can be replaced by other supplements such as anticoagulant citrate dextrose formula-A (ACD-A) or citrate phosphate dextrose (CPD). BSA can be replaced by other proteins such as human serum albumin, human serum or fetal calf serum. Buffers or media containing Ca2+ or Mg2+ are not recommended for use.
● MACS Columns and MACS Separators: CD3+ cells can be enriched by using MS, LS or XS Columns (positive selection). CD3 MicroBeads can be used for depletion of CD3+ cells on LD, CS or D Columns. Positive selection or depletion can also be performed by using the autoMACS Separator. When working with anticoagulated peripheral blood or buffy coat, peripheral blood mononuclear cells (PBMCs) should be isolated by density gradient centrifugation.
▲ Note: Remove platelets after density gradient separation: resuspend cell pellet in buffer and centrifuge at 200× g for 10−15 minutes at 20 °C. Carefully remove supernatant. Repeat washing step and carefully remove supernatant. When working with tissues, prepare a single-cell suspension by a standard preparation method. ▲ Note: Dead cells may bind non-specifically to MicroBeads. To remove dead cells, we recommend using density gradient centrifugation or the Dead Cell Removal Kit.
▲ Work fast, keep the cells cold, and use pre-cooled solutions. This will prevent capping of antibodies on the cell surface and non-specific cell labeling. ▲ Volumes for magnetic labeling given below are for up to 107 total cells. When working with fewer than 107 cells, use the same volumes as indicated. When working with higher cell numbers, scale up all reagent volumes and total volumes accordingly (e.g. for 2× 107 total cells, use twice the volume of all indicated reagent volumes and total volumes).
▲ For optimal performance it is important to obtain a single-cell suspension before magnetic separation. Pass cells through 30 µm nylon mesh (Pre-Separation Filters) to remove cell clumps which may clog the column.
2. Centrifuge cell suspension at 300× g for 10 minutes. Pipette off supernatant completely.
3. Resuspend cell pellet in 80 µL of buffer per 107 total cells.
4. Add 20 µL of CD3 MicroBeads per 107 total cells.
5. Mix well and incubate for 15 minutes at 2−8 °C. ▲ Note: Working on ice may require increased incubation times. Higher temperatures and/or longer incubation times lead to non-specific cell labeling.
6. (Optional) Add staining antibodies, e.g. add 10 µL of CD3-FITC and incubate for 5 minutes at 2−8 °C.
7. Wash cells by adding 1−2 mL of buffer per 107 cells and centrifuge at 300× g for 10 minutes. Pipette off supernatant completely.
8. Resuspend up to 108 cells in 500 µL of buffer. ▲ Note: For higher cell numbers, scale up buffer volume accordingly. ▲ Note: For depletion with LD Columns, resuspend up to 1.25× 108 cells in 500 µL of buffer.
1. Place column in the magnetic field of a suitable MACS Separator.
2. Prepare column by rinsing with appropriate amount of buffer:
3. Apply cell suspension onto the column.
4. Collect unlabeled cells which pass through and wash column with appropriate amount of buffer. Perform washing steps by adding buffer three times, each time once the column reservoir is empty. Collect total effluent. This is the unlabeled cell fraction.
5. Remove column from the separator and place it on a suitable collection tube.
6. Pipette appropriate amount of buffer onto the column. Immediately flush out fraction with the magnetically labeled cells by firmly applying the plunger supplied with the column. ▲ Note: To increase the purity of the magnetically labeled fraction, it can be passed over a new, freshly prepared column. For instructions on the column assembly and the separation, refer to the "XS Column data sheet".
1. Place LD Column in the magnetic field of a suitable MACS Separator.
2. Prepare column by rinsing with 2 mL of buffer.
4. Collect unlabeled cells which pass through and wash column with 2× 1 mL of buffer. Collect total effluent. This is the unlabeled cell fraction.
1. Assemble CS Column and place it in the magnetic field of a suitable MACS Separator.
2. Prepare column by filling and rinsing with 60 mL of buffer. Attach a 22G flow resistor to the 3-way-stopcock of the assembled column.
4. Collect unlabeled cells which pass through and wash column with 30 mL buffer from the top. ▲ Refer to the "autoMACS User Manual" for instructions on how to use the autoMACS Separator.
1. Prepare and prime autoMACS Separator.
2. Place tube containing the magnetically labeled cells in the autoMACS Separator. For a standard separation, choose following separation programs: ▲ Note: Program choice depends on the isolation strategy, the strength of magnetic labeling and the frequency of magnetically labeled cells. For details see autoMACS User Manual: "autoMACS Cell Separation Programs".
3. When using the program "Possel", collect positive fraction (outlet port "pos1"). This is the When using the program "Depletes", collect unlabeled fraction (outlet port "neg1"). This is the CD3- cell fraction. SophMag®手动磁分选套装
相关资料下载:产品说明书(.pdf)(点击从官网下载)
04荣誉与资质
该品牌暂未上传荣誉证书与资质文件。以下是平台可核验的公开信息,未上传项如实标注,不做推断。
- 营业执照未上传
- 品牌授权未上传
- 产品检测报告未上传
- 会员身份
- 收费会员
- 经营身份
- 原厂
- 成立年份
- 2021 年
- 所在地
- 上海
- 收录条目
- 334 个
- 平台核验
- 平台代管
05品牌与供应商
苏州欣协生物科技有限公司(以下简称欣协生物)始创于2021年,专注于细胞和基因治疗(CGT)领域的科创研发,竭诚为全球生命科学提供自动化、定制化、一体化的整体解决方案服务。
品牌资料由厂商公开信息与授权渠道核对整理;条目参数与价格以最终报价单为准。
06同类条目
同一子类内的条目才具备可比性。跨子类比较参数通常没有意义。
07同品牌其他条目
欣协生物 在本目录共 334 个条目,除本条外还有:
科研在线(TeleVM). CD3 MicroBeads, human (92-01[EB/OL]. 产品目录, 2026-10-31. https://www.suprotek.cn/products/item/cd3-microbeads-human-92-01.html.
TeleVM. (2026, October 31). CD3 MicroBeads, human (92-01. 产品目录. https://www.suprotek.cn/products/item/cd3-microbeads-human-92-01.html
@misc{biocsp_item_cd3_microbeads_human_92_01,
title = {CD3 MicroBeads, human (92-01},
author = {{科研在线}},
year = {2026},
howpublished = {产品目录},
note = {更新于 2026-10-31,产品目录},
url = {https://www.suprotek.cn/products/item/cd3-microbeads-human-92-01.html}
}
GB/T 7714 用于中文论文与报告;APA 7 用于英文期刊;BibTeX 可直接导入 Zotero、EndNote 或 LaTeX。
许可:CC BY-NC 4.0 · 转载注明来源